Rosetta - a Control System for Stepper Motors on Ornamental Turning Machines


Overview


Rosetta

Rosetta is a control system for using stepper motors on the rose engine lathe and other ornamental turning machines. It was developed by ornamental turners - Rich Colvin & Chuck Peplinski, and is based on LinuxCNC running on a Raspberry Pi 5.

Rosetta's own screens do the everyday tasks (indexing, synchronized movement, threading) from menus and buttons, so the turner does not need to know G-code; for more complex work, it runs standard G-code programs, including ones its own design programs write. LinuxCNC is normally hard to set up, so Rosetta has its own settings program for choosing which device is on which motor, tuning the motors, and adding accessories.

Key Features:

  • Up to 10 stepper motors: 6 from the base box, and 4 more from an optional expansion box
    • 2 spindles - the work spindle and a rosette phaser / multiplier - which can run together at different speeds
    • Linear axes (X, Z, U, V, W) and rotary / angular axes (A, B, C), e.g. a cross slide, a curvilinear slide, or a rotating cutter
    • Any device can be plugged into any channel; the settings program says which is which
  • Built from off-the-shelf parts: a Raspberry Pi 5, a Mesa 7i92 FPGA card and StepperOnline DM542T stepper drives
  • Main screen, without G-code:
    • Indexing of any axis or spindle, in degrees or divisions, with a count of the indexes made
    • Synchronized movement - several axes move together and finish together (e.g. the spindle turning while a slide advances)
    • Threading, including multi-start threads, cut by turning the spindle and moving the slide together
    • A progress bar while a program runs, and a Pause / Continue button
  • Rosette Designer - software-defined rosettes:
    • Holtzapffel shapes (from the Holtzapffel & Co. guide's drawings), sine waves, polygons, and lotus and Tudor shapes
    • Rocking, pumping, or both at once, each with its own rosette and phase
    • An ellipse set by its length and width, with a second rosette's pattern wrapped around it
    • Amplitude, number of lobes and phase set as numbers, and the pattern drawn on the screen before cutting
    • Roughing passes, a slower finishing pass, and spring passes
  • Geometric Chuck Designer - a multi-stage geometric chuck:
    • Up to 5 stages, with the pattern drawn on the screen
    • Figures from T. S. Bazley's Index to the Geometric Chuck (1875) filled in by figure number (being added)
    • Patterns through the centre allowed, with a warning
  • A Check Circle program, to set the cutter's starting radius when the axis of rotation is hard to measure
  • Optional accessories: limit switches (up to 6), an emergency stop button, an external pause button, a signal tower (green / red lights and a siren), sounds when a program finishes or pauses, and alerts to the turner's phone
  • Back up and restore to a USB flash drive, and software updates from the Applications menu

 

H2

######################################################################## ### Additional pictures of this device ########################################################################

Additional pictures of this device

######################################################################## ### Examples of work produced with this device ########################################################################

Examples of work produced with this device

######################################################################## ### Examples of this device in use ########################################################################

Examples of this device in use

######################################################################## ### Usage Notes ########################################################################

Usage Notes

######################################################################## ### How it works ########################################################################

How it Works

######################################################################## ### Notes on one ########################################################################

Notes on Making One

######################################################################## ### Sources for buying one ########################################################################

Sources for Buying One

######################################################################## ### More Information ########################################################################

More Information

Published Articles

Books and Papers

Web Sites

Presentations

Other

########## Standard Footer for all pages ##########

About this Site

Disclaimer: eMail comments to me at OTBookOfKnowledge @ Gmail.com. The process of woodturning involves the use of tools, machinery and materials which could cause injury or be a health hazard unless proper precautions are taken, including the wearing of appropriate protective equipment.