Leadscrew


Overview

A leadscrew turns rotation into straight-line movement: turning the screw moves a nut along it, and the slide fixed to the nut moves with it. Most cross slides, curvilinear slides and other slides on ornamental turning machines are moved by a leadscrew, turned by a handwheel or a stepper motor.


 

Pitch, Lead, and Starts

  • Pitch - the distance from one thread to the next. Metric screws give it in mm; imperial screws give threads per inch (TPI) instead, so a 10 TPI screw has a pitch of 0.100".
  • Starts - how many separate threads are wound side by side. Look at the end of the screw and count where threads begin: most screws have one, but two or four are common.
  • Lead - how far one turn moves the nut:
lead = pitch × starts

A 10 TPI single-start screw moves 0.100" a turn - one turn of a dial indicator, which makes it easy to check. A metric screw with a 2 mm pitch and 4 starts (sold as "T8 × 8", common on 3D printers) moves 8 mm a turn - four times as far as a single-start screw of the same pitch.

  • Count the starts before working out any settings. A multi-start screw moves several times as far as you might expect from its pitch. When first trying a motor-driven slide, ask for a small move (0.010", or 0.25 mm) and measure it, before trusting a larger one.

Screws with more starts move the slide faster for each turn, but need more force to turn, and are easier to push round from the slide's end (back-drive) - so the cutting force can move the slide more easily.


 

Kinds of Leadscrew

  • Acme (imperial) and trapezoidal (metric) screws have a sliding nut. They are cheap and robust, but have some backlash; a split, spring-loaded "anti-backlash" nut takes up most of it.
  • Ball screws have balls rolling between the screw and the nut. They have very little friction and backlash, but cost more, and are easily pushed round by the load.

 

Driving a Leadscrew with a Motor

The controller needs to know how many pulses move the slide one unit - its scale (see Stepper Motor: Scale):

pulses per unit = pulses per motor turn × gear ratio ÷ lead

For example, a motor with 20-tooth pulley driving a 120-tooth pulley on a 10 TPI single-start screw (lead 0.100"), with the stepper drive at 6,400 pulses per motor turn: 6,400 × 6 ÷ 0.100 = 384,000 pulses per inch.

The tables below give the pulses for common screws driven directly (no gearing) at 6,400 pulses per motor turn. For gearing, multiply by the gear ratio; for a different drive setting, multiply by (that setting ÷ 6,400).

Metric leadscrews

Pitch Starts Lead Pulses per mm Pulses per inch
1 mm 1 1 mm 6,400.0 162,560
1 mm 2 2 mm 3,200.0 81,280
1 mm 4 4 mm 1,600.0 40,640
2 mm 1 2 mm 3,200.0 81,280
2 mm 2 4 mm 1,600.0 40,640
2 mm 4 8 mm 800.0 20,320
3 mm 1 3 mm 2,133.3 54,187
3 mm 2 6 mm 1,066.7 27,093
3 mm 4 12 mm 533.3 13,547
4 mm 1 4 mm 1,600.0 40,640
4 mm 2 8 mm 800.0 20,320
4 mm 4 16 mm 400.0 10,160

Imperial leadscrews

TPI Starts Lead Pulses per mm Pulses per inch
5 1 0.2000" 1,259.8 32,000
8 1 0.1250" 2,015.7 51,200
10 1 0.1000" 2,519.7 64,000
16 1 0.0625" 4,031.5 102,400
20 1 0.0500" 5,039.4 128,000

The controller never sends part of a pulse, but these numbers are used to work out the pulses for every distance (e.g. 1.25" × pulses per inch), so keep the decimals.

######################################################################## ### Additional pictures of this device ########################################################################

Additional pictures of this device

######################################################################## ### Examples of this device in use ########################################################################

Examples of this device in use

######################################################################## ### More Information ########################################################################

More Information

Published Articles

Books and Papers

Web Sites

  • More information is available on Wikipedia at Leadscrew.

Presentations

Other

########## Standard Footer for all pages ##########

About this Site

Disclaimer: eMail comments to me at OTBookOfKnowledge @ Gmail.com. The process of woodturning involves the use of tools, machinery and materials which could cause injury or be a health hazard unless proper precautions are taken, including the wearing of appropriate protective equipment.